65637bd9



11.8. Support of a back brake

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and establish on supports.
2. Remove a wheel.
3. Release a cover of a cable of the emergency brake, disconnect a cable from the lever on a support.
4. For decrease in losses of liquid densely wrap a stopper of a tank having laid a polyethylene film, or press hoses.
5. Clear the ring union of a hose and turn off a bolt, muffle openings.
6. Remove two laying.
7. Remove blocks.
8. Turn off a bolt of the top finger of a support.
9. Remove a support from an arm.
10. If necessary it is possible to remove a support arm from a pin.

Dismantling

PERFORMANCE ORDER
1. Carefully clear a support.
2. Get fingers for heads of bolts which screw in fingers.
3. Remove rubber covers of fingers.
4. Turn out (to rotate counterclockwise) and get the piston from the cylinder.
5. Remove a cover.
6. Squeeze a cylinder spring, having pressed on a cap, and take a lock ring from a cylinder flute.
7. Gradually releasing a spring, get a spring ring, a cap, a spring, a lock plate, a pusher and a strut.
8. A wooden stick get a cylinder sealant.
9. Unhook a spring from the lever of the emergency brake, turn off a nut and remove the lever from a support.
10. Wash out all details in pure brake fluid or alcohol.
11. All a sealant and covers are subject to obligatory replacement.
12. Check a condition of a support, especially carefully examine the piston and the internal surface of the cylinder, replace worn-out details. The support or an arm of a support separately in the spare part are not delivered.
13. Minor defects on the cylinder are eliminated with polishing with a small skin whereas the piston with the same defects is subject to obligatory replacement. It is forbidden to polish the piston.
14. Check a condition of carvings on support fingers, the side play of fingers in a support has to be absent.
15. Blow channels of brake fluid.
16. Before assembly check purity of all details.
17. Dress a new cover on the clown of the lever of the emergency brake.
18. Establish a spring, a washer and tighten a nut.
19. Grease the clown with brake fluid and establish on a support.
20. Make sure that at turn of the lever the groove in the clown is combined with an opening in a pusher.
21. Dress a lever spring.
22. Dip a new sealant of the cylinder into liquid and establish in a cylinder flute.
23. Dress a new sealing ring on a pusher and oil rubber a strut and a pusher.
24. Establish all details in a support.
25. Establish a lock plate so that the groove fell on a flat part of a pusher, and camber coincided with deepening in a support.
26. Establish a spring lock ring.
27. Establish a spring and a cap, squeeze a spring and establish a spring lock ring.
28. Oil a cylinder cover edge rubber and dress on the piston.
29. Grease with brake fluid the piston and walls of the cylinder in a support, screw the piston in the cylinder, rotating clockwise.
30. Dress the second edge of a cover on a support.
31. Dress new covers on support fingers.
32. Replace the rubber plug on the top finger.
33. Before installation in a support grease fingers with brake fluid.

Installation

PERFORMANCE ORDER
1. Establish a support arm on a pin, tighten bolts.
2. Establish a support, grease a carving of a bolt of the top finger with the fixing structure and wrap a bolt with the set moment.
3. Establish blocks.
4. Check freedom of movement of a support in an arm.
5. Attach a hose, having established two laying and having tightened a bolt of the ring union.
6. Attach a cable of the emergency brake to the lever, establish an arm. On a part of cars insert a cable cover into a bracket, and combine a ledge on an arm with dredging on a support body.
7. Remove polyethylene laying from a tank stopper (or remove collars from hoses).
8. Remove air from a wheel brake hydraulic actuator (if integrity of other contours was not broken).
9. Press several times a brake pedal.
10. Establish wheels, lower the car.
11. Before departure check work of brakes.